1、檢查風機底座必須牢固，電機、電機支架等部分螺栓必須鎖緊；

Make sure the blower base fastness and tighten all bolts.

2、風機進風口必須清潔，排除任何雜物，并安裝進口消音器，鎖緊；

Ensure no foreign matters stay on air inlet, install inlet silencer and tighten.

3、檢查三角帶松緊程度，皮帶輪確保在一條直線上；

Check V-belts tightness and ensure a pair of pulleys on a straight line.

4、電機轉向根據風機要求調好，禁止風機逆轉；

Adjust motor rotation direction, ensure no reversion.

5、檢查油箱有無潤滑油（N220中負荷工業齒輪油），風機靜止?fàn)顟B(tài)下油位不要高于油窗中心位置；若高于中心，多余的油會從墻板散熱孔溢出。

Check if there’s lubricating oil in oil tank(N220 Industrial middle load gear oil). Oil level should stay below the center of oil window when the blower is static. Or, surplus oil will overflow from ventilation holes on side plates.

6、確保出風口管道暢通無阻(單向閥的方向要正確，閘閥、蝶閥等要打開)，禁止風機帶負荷起動；

Ensure outlet is unobstructed (Check valve with correct direction, keep gate valve, butterfly valve open), and forbid blower overload operation.

￥◇d┗@ㄜ"話鶇颮己￥◇d┗@ㄜ"造作啊

7、管道各部分安裝正確（詳情請參閱羅茨風機、真空泵使用說明書）,風口、彈性接頭、進、出口消音器、單向閥，連接牢固；hdfj11com

Check pipes are installed correctly (Please refer to roots blower/vacuum pump operation manual)and ensure the connections (air vent,flexible joint, inlet&outlet silencers, check valve)are fastness. 

8、一切就緒，開機前先用手輕輕轉動皮帶輪，確保風機輕輕轉動，如有異物請立即排出，方可開機。

Rotate the pulley by hand before starting, to confirm no foreign matters is inside, then start up.

9、 壓力表的注意事項：首先確保壓力表頂端的排氣口通暢。開機前務必先將壓力表開關處于打開狀態，以免造成壓力表的損壞。

Pressure Gauge NOTICE: Ensure air vent which is on top of pressure gauge is unobstructed. Meanwhile, keep gauge switch be open when start up blower, in case pressure gauge damages.

華東風機專業生產羅茨鼓風機，如果您有維修和采購方面的問題，可以聯系我們的全國免費客服熱線4008-797-786

推薦閱讀：三葉羅茨鼓風機產品列表